State Less The Band Technology Site

Posts Tagged ‘router’

Passing the BSCI exam and earning your CCNP is all about knowing the details, and when it comes to EIGRP SIA routes, there are plenty of details to know. A quick check in a search engine for “troubleshoot SIA” will bring up quite a few matches. Troubleshooting SIA routes is very challengin in that there’s no one reason they occur.

View the EIGRP topology table with the show ip eigrp topology command, and you’ll see a code next to every successor and feasible successor. A popular misconception is that we want these routes to have an “A” next to them – so they’re active. That’s what we want, right? Active routes sound good, right?

Well, they sound good, but they’re not. If a route shows as Active in the EIGRP topology table, that means that DUAL is currently calculating that route, and it’s currently unusable. When a route is Passive (“P), that means it’s not being recalculated and it’s a usable route.

Generally, a route shown as Active is going to be there for a very short period of time by the time you repeat the command, hopefully that Active route has gone Passive. Sometimes that doesn’t happen, though, and the route becomes SIA – Stuck In Active.
Read the rest of this entry »

To earn your CCNP certification and pass the BCMSN exam, you’ve got to know what HSRP does and the many configurable options. While the operation of HSRP is quite simple (and covered in a previous tutorial), you also need to know how HSRP arrives at the MAC address for the virtual router – as well as how to configure a new MAC for this virtual router. This puts us in the unusual position of creating a physical address for a router that doesn’t exist!

The output of show standby for a two-router HSRP configuration is shown below.

R2#show standby

Ethernet0 – Group 5

Local state is Standby, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 0.776

Virtual IP address is 172.12.23.10 configured

Active router is 172.12.23.3, priority 100 expires in 9.568

Standby router is local

1 state changes, last state change 00:00:22

R3#show standby

Ethernet0 – Group 5

Local state is Active, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 2.592

Virtual IP address is 172.12.23.10 configured

Active router is local

Standby router is 172.12.23.2 expires in 8.020

Virtual mac address is 0000.0c07.ac05

2 state changes, last state change 00:02:08

R3 is in Active state, while R2 is in Standby. The hosts are using the 172.12.123.10 address as their gateway, but R3 is actually handling the workload. R2 will take over if R3 becomes unavailable.
Read the rest of this entry »

Defined in RFC 2281, HSRP is a Cisco-proprietary protocol in which routers are put into an HSRP router group. Along with dynamic routing protocols and STP, HSRP is considered a high-availability network service, since all three have an almost immediate cutover to a secondary path when the primary path is unavailable.

One of the routers will be selected as the primary (“Active”, in HSRP terminology), and that primary will handle the routing while the other routers are in standby, ready to handle the load if the primary router becomes unavailable. In this fashion, HSRP ensures a high network uptime, since it routes IP traffic without relying on a single router.

The hosts using HSRP as a gateway don’t know the actual IP or MAC addresses of the routers in the group. They’re communicating with a pseudorouter, a “virtual router” created by the HSRP configuration. This virtual router will have a virtual MAC and IP adddress as well.

The standby routers aren’t just going to be sitting there, though! By configuring multiple HSRP groups on a single interface, HSRP load balancing can be achieved.

Before we get to the more advanced HSRP configuration, we better get a basic one started! We’ll be using a two-router topology here, and keep in mind that one or both of these routers could be multilayer switches as well. For ease of reading, I’m going to refer to them only as routers.

R2 and R3 will both be configured to be in standby group 5. The virtual router will have an IP address of 172.12.23.10 /24. All hosts in VLAN 100 should use this address as their default gateway.

R2(config)#interface ethernet0

R2(config-if)#standby 5 ip 172.12.23.10

R3(config)#interface ethernet0

R3(config-if)#standby 5 ip 172.12.23.10

The show command for HSRP is show standby, and it’s the first command you should run while configuring and troubleshooting HSRP. Let’s run it on both routers and compare results.
Read the rest of this entry »

A CCNA or CCNP candidate who wants to be totally prepared for their exams is going to put together a home lab to practice on. With used Cisco routers and switches more affordable and plentiful then ever before, there’s really no excuse to not have one!

With the many different models available, there is some understandable confusion among future CCNAs and CCNPs about which routers to buy and which ones to avoid. You can take almost any set of Cisco routers and put together a home lab; part of the learning process is taking what equipment you have available and putting together your own lab! For those of you preparing to start your home lab or add to your existing one, this article will list the routers I use in my Cisco pods. You certainly don’t have to have all this equipment, but this will give you some good ideas on how to get started.

The most versatile router you can get for your CCNA / CCNP home lab is a 2520. These routers come with four serial ports, one ethernet port, and one BRI interface for ISDN practice. This mix of interfaces means you can actually use it as a frame relay switch while using the ethernet and BRI ports for routing. (There is no problem with using a lab router as both your frame relay switch and a practice router; for a frame relay switch sample configuration, visit my website!)

My pods consist of five routers and two switches, and three of the five routers are 2520s, due to their versatility. A recent ebay search showed these routers selling for $99 – $125, an outstanding value for the practice you’re going to get.

I also use 2501s in my home labs. These have fewer interfaces, but the combination of two serial interfaces and one ethernet interface allows you to get plenty of practice.

A combination that works very well is using three 2520s; one as my dedicated frame relay switch, one as R1, and another as R2. Add a 2501 as R3, and you can have a frame cloud connecting R1, R2, and R3, a direct serial connection between R1 and R3, an Ethernet segment that includes all three routers, and an ISDN connection between R1 and R2 if you have an ISDN simulator. That combination will allow you to get a tremendous amount of practice for the exams, and you can always sell it when you’re done!

2501s are very affordable, with many in the $50 range on ebay. It’s quite possible to get three 2520s and one 2501 for less than $500 total, and you can get most of that money back if you choose to sell it when you’re done.
Read the rest of this entry »