State Less The Band Technology Site

Posts Tagged ‘hsrp’

When you’re working on your BCMSN exam on your way to CCNP certification, you’ll read at length about how Cisco routers and multilayer switches can work to provide router redundancy – but there’s another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.

In the following example, three physical servers have been placed into the SRB group ServFarm. They’re represented to the hosts as the virtual server 210.1.1.14.

The hosts will seek to communicate with the server at 210.1.1.14, not knowing that they’re actually communicating with the routers in ServFarm. This allows quick cutover if one of the physical servers goes down, and also serves to hide the actual IP addresses of the servers in ServFarm.

The basic operations of SLB involves creating the server farm, followed by creating the virtual server. We’ll first add 210.1.1.11 to the server farm:

MLS(config)# ip slb serverfarm ServFarm

MLS(config-slb-sfarm)# real 210.1.1.11

MLS(config-slb-real)# inservice
Read the rest of this entry »

To earn your CCNP certification and pass the BCMSN exam, you’ve got to know what HSRP does and the many configurable options. While the operation of HSRP is quite simple (and covered in a previous tutorial), you also need to know how HSRP arrives at the MAC address for the virtual router – as well as how to configure a new MAC for this virtual router. This puts us in the unusual position of creating a physical address for a router that doesn’t exist!

The output of show standby for a two-router HSRP configuration is shown below.

R2#show standby

Ethernet0 – Group 5

Local state is Standby, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 0.776

Virtual IP address is 172.12.23.10 configured

Active router is 172.12.23.3, priority 100 expires in 9.568

Standby router is local

1 state changes, last state change 00:00:22

R3#show standby

Ethernet0 – Group 5

Local state is Active, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 2.592

Virtual IP address is 172.12.23.10 configured

Active router is local

Standby router is 172.12.23.2 expires in 8.020

Virtual mac address is 0000.0c07.ac05

2 state changes, last state change 00:02:08

R3 is in Active state, while R2 is in Standby. The hosts are using the 172.12.123.10 address as their gateway, but R3 is actually handling the workload. R2 will take over if R3 becomes unavailable.
Read the rest of this entry »

Defined in RFC 2281, HSRP is a Cisco-proprietary protocol in which routers are put into an HSRP router group. Along with dynamic routing protocols and STP, HSRP is considered a high-availability network service, since all three have an almost immediate cutover to a secondary path when the primary path is unavailable.

One of the routers will be selected as the primary (“Active”, in HSRP terminology), and that primary will handle the routing while the other routers are in standby, ready to handle the load if the primary router becomes unavailable. In this fashion, HSRP ensures a high network uptime, since it routes IP traffic without relying on a single router.

The hosts using HSRP as a gateway don’t know the actual IP or MAC addresses of the routers in the group. They’re communicating with a pseudorouter, a “virtual router” created by the HSRP configuration. This virtual router will have a virtual MAC and IP adddress as well.

The standby routers aren’t just going to be sitting there, though! By configuring multiple HSRP groups on a single interface, HSRP load balancing can be achieved.

Before we get to the more advanced HSRP configuration, we better get a basic one started! We’ll be using a two-router topology here, and keep in mind that one or both of these routers could be multilayer switches as well. For ease of reading, I’m going to refer to them only as routers.

R2 and R3 will both be configured to be in standby group 5. The virtual router will have an IP address of 172.12.23.10 /24. All hosts in VLAN 100 should use this address as their default gateway.

R2(config)#interface ethernet0

R2(config-if)#standby 5 ip 172.12.23.10

R3(config)#interface ethernet0

R3(config-if)#standby 5 ip 172.12.23.10

The show command for HSRP is show standby, and it’s the first command you should run while configuring and troubleshooting HSRP. Let’s run it on both routers and compare results.
Read the rest of this entry »