State Less The Band Technology Site

Posts Tagged ‘free’

Passing the BSCI exam and earning your CCNP is all about knowing the details, and when it comes to EIGRP SIA routes, there are plenty of details to know. A quick check in a search engine for “troubleshoot SIA” will bring up quite a few matches. Troubleshooting SIA routes is very challengin in that there’s no one reason they occur.

View the EIGRP topology table with the show ip eigrp topology command, and you’ll see a code next to every successor and feasible successor. A popular misconception is that we want these routes to have an “A” next to them – so they’re active. That’s what we want, right? Active routes sound good, right?

Well, they sound good, but they’re not. If a route shows as Active in the EIGRP topology table, that means that DUAL is currently calculating that route, and it’s currently unusable. When a route is Passive (“P), that means it’s not being recalculated and it’s a usable route.

Generally, a route shown as Active is going to be there for a very short period of time by the time you repeat the command, hopefully that Active route has gone Passive. Sometimes that doesn’t happen, though, and the route becomes SIA – Stuck In Active.
Read the rest of this entry »

To earn your CCNP certification and pass the BCMSN exam, you’ve got to know what HSRP does and the many configurable options. While the operation of HSRP is quite simple (and covered in a previous tutorial), you also need to know how HSRP arrives at the MAC address for the virtual router – as well as how to configure a new MAC for this virtual router. This puts us in the unusual position of creating a physical address for a router that doesn’t exist!

The output of show standby for a two-router HSRP configuration is shown below.

R2#show standby

Ethernet0 – Group 5

Local state is Standby, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 0.776

Virtual IP address is 172.12.23.10 configured

Active router is 172.12.23.3, priority 100 expires in 9.568

Standby router is local

1 state changes, last state change 00:00:22

R3#show standby

Ethernet0 – Group 5

Local state is Active, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 2.592

Virtual IP address is 172.12.23.10 configured

Active router is local

Standby router is 172.12.23.2 expires in 8.020

Virtual mac address is 0000.0c07.ac05

2 state changes, last state change 00:02:08

R3 is in Active state, while R2 is in Standby. The hosts are using the 172.12.123.10 address as their gateway, but R3 is actually handling the workload. R2 will take over if R3 becomes unavailable.
Read the rest of this entry »

Defined in RFC 2281, HSRP is a Cisco-proprietary protocol in which routers are put into an HSRP router group. Along with dynamic routing protocols and STP, HSRP is considered a high-availability network service, since all three have an almost immediate cutover to a secondary path when the primary path is unavailable.

One of the routers will be selected as the primary (“Active”, in HSRP terminology), and that primary will handle the routing while the other routers are in standby, ready to handle the load if the primary router becomes unavailable. In this fashion, HSRP ensures a high network uptime, since it routes IP traffic without relying on a single router.

The hosts using HSRP as a gateway don’t know the actual IP or MAC addresses of the routers in the group. They’re communicating with a pseudorouter, a “virtual router” created by the HSRP configuration. This virtual router will have a virtual MAC and IP adddress as well.

The standby routers aren’t just going to be sitting there, though! By configuring multiple HSRP groups on a single interface, HSRP load balancing can be achieved.

Before we get to the more advanced HSRP configuration, we better get a basic one started! We’ll be using a two-router topology here, and keep in mind that one or both of these routers could be multilayer switches as well. For ease of reading, I’m going to refer to them only as routers.

R2 and R3 will both be configured to be in standby group 5. The virtual router will have an IP address of 172.12.23.10 /24. All hosts in VLAN 100 should use this address as their default gateway.

R2(config)#interface ethernet0

R2(config-if)#standby 5 ip 172.12.23.10

R3(config)#interface ethernet0

R3(config-if)#standby 5 ip 172.12.23.10

The show command for HSRP is show standby, and it’s the first command you should run while configuring and troubleshooting HSRP. Let’s run it on both routers and compare results.
Read the rest of this entry »

CCNP exam success, particularly on the BSCI exam, demands you understand the details of route summarization. This skill not only requires that you have a comfort level with binary conversions, but you have to know how and where to apply route summarization with each individual protocol.

You also have to know the “side effects” of route summarization. With OSPF, there will actually be an extra interface created at the point of summarization, and this catches a lot of CCNP candidates by surprise. Let’s take a look at the null0 interface and how it relates to OSPF summarization.

On R1, the following networks are redistributed into OSPF, and then summarized.

interface Loopback16

ip address 16.16.16.16 255.0.0.0

interface Loopback17

ip address 17.17.17.17 255.0.0.0

interface Loopback18

ip address 18.18.18.18 255.0.0.0

interface Loopback19

ip address 19.19.19.19 255.0.0.0

R1(config)#router ospf 1 Read the rest of this entry »