State Less The Band Technology Site

Posts Tagged ‘exam’

Passing the BCMSN exam and getting one step closer to the CCNP certification means learning and noticing details that you were not presented with in your CCNA studies. (Yes, I know – you had more than enough details then, right?) One protocol you’ve got to learn more details about is VTP, which seemed simple enough in your CCNA studies! Part of learning the details is mastering the fundamentals, so in this tutorial we’ll review the basics of VTP.

In show vtp status readouts, the “VTP Operating Mode” is set to “Server” by default. The more familiar term for VTP Operating Mode is simply VTP Mode, and Server is the default. It’s through the usage of VTP modes that we can place limits on which switches can delete and create VLANs.

In Server mode, a VTP switch can be used to create, modify, and delete VLANs. This means that a VTP deployment has to have at least one switch in Server mode, or VLAN creation will not be possible. Again, this is the default setting for Cisco switches.

Switches running in Client mode cannot be used to create, modify, or delete VLANs. Clients do listen for VTP advertisements and act accordingly when VTP advertisements notify the Client of VLAN changes.
Read the rest of this entry »

To pass the CCNA exam and earn this important certification, you’ve got to know switching inside and out. While you’re learning all the basic switching theory, make sure to spend some time with the one of three switching modes Cisco routers can use.

Store-and-Forward is exactly what it sounds like. The entire frame will be stored before it is forwarded. This mode allows for the greatest amount of error checking, since a CRC (Cyclical Redundancy Check) is run against the frame before it is forwarded. If the frame contains an error, it is discarded. If there’s no problem with the frame, the frame is then forwarded to its proper destination.

While store-and-forward does perform error checking, the delay in processing the frame while this error check is run results in higher latency than the other modes you’re about to read about. The latency time can also vary, since not all frames are the same size.

Cut-through switching copies only the destination MAC address into its memory before beginning to forward the frame. Since the frame is being forwarded as soon as the destination MAC is read, there is less latency than store-and-forward. The drawback is that there is no error checking.

There is a middle ground, fragment-free switching. Only part of the frame is copied to memory before it is forwarded, but it’s the first 64 bytes of the frame, not just the destination MAC. (Why? Because if there is a problem with the frame, it’s most likely in the first 64 bytes.) There is a little more error checking than cut-through, but not as much latency as with store-and-forward.
Read the rest of this entry »

Whether you’re on the road to the CCNA, CCNP, MCSE, or you’re on any other computer certification track, the odds are that sooner or later, you’re going to fail an exam. It’s happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You’ve probably seen charts showing the growth of an industry or a business — you know, the ones that go from left to right, and look kind of jagged. The line goes up for a while, then down a bit, then up some more, then down a little.

The key? While every business has its setbacks, the net result is that the line goes up and progress is made. That’s how you want your certification pursuit and your career to go as well – upward!

I’m not asking you to be happy about failing an exam. You’re allowed to get mad for a few minutes, vow to never take another exam again, and be disappointed. What you’re not allowed to do is stay that way.
Read the rest of this entry »

CCNA and CCNP candidates who have their own Cisco home labs often email me about an odd situation that occurs when they erase a switch’s configuration. Their startup configuration is gone, as they expect, but the VLAN and VTP information is still there!

Sounds strange, doesn’t it? Let’s look at an example. On SW1, we run show vlan brief and see in this abbreviated output that there are three additional vlans in use:

SW1#show vlan br

10 VLAN0010 active

20 VLAN0020 active

30 VLAN0030 active

We want to totally erase the router’s startup configuration, so we use the write erase command, confirm it, and reload without saving the running config:

SW1#write erase

Erasing the nvram filesystem will remove all configuration files! Continue?

[confirm]

[OK]

Erase of nvram: complete

00:06:00: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram

SW1#reload

System configuration has been modified. Save? [yes/no]: n

Proceed with reload? [confirm]

The router reloads, and after exiting setup mode, we run show vlan brief again. And even though the startup configuration was erased, the vlans are still there!

Switch#show vlan br

10 VLAN0010 active

20 VLAN0020 active

30 VLAN0030 active
Read the rest of this entry »