State Less The Band Technology Site

Posts Tagged ‘certification’

When you’re working on your BCMSN exam on your way to CCNP certification, you’ll read at length about how Cisco routers and multilayer switches can work to provide router redundancy – but there’s another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.

In the following example, three physical servers have been placed into the SRB group ServFarm. They’re represented to the hosts as the virtual server 210.1.1.14.

The hosts will seek to communicate with the server at 210.1.1.14, not knowing that they’re actually communicating with the routers in ServFarm. This allows quick cutover if one of the physical servers goes down, and also serves to hide the actual IP addresses of the servers in ServFarm.

The basic operations of SLB involves creating the server farm, followed by creating the virtual server. We’ll first add 210.1.1.11 to the server farm:

MLS(config)# ip slb serverfarm ServFarm

MLS(config-slb-sfarm)# real 210.1.1.11

MLS(config-slb-real)# inservice
Read the rest of this entry »

To pass the CCNP exams, you’ve got to master Quality of Service, and the first step in doing so is knowing the differences between the different QoS types.

Now this being Cisco, we can’t just have one kind of QoS! We’ve got best-effort delivery, Integrated Services, and Differentiated Services. Let’s take a quick look at all three.

Best-effort is just what it sounds like – routers and switches making their “best effort” to deliver data. This is considered QoS, but it’s kind of a “default QoS”. Best effort is strictly “first in, first out” (FIFO).

An entire path from Point A to Point B will be defined in advance when Integrated Services are in effect. Integrated Services is much like the High-Occupancy Vehicle lanes found in many larger cities. If your car has three or more people in it, you’re considered a “priority vehicle” and you can drive in a special lane with much less congestion than regular lanes. Integrated Services will create this lane in advance for “priority traffic”, and when that traffic comes along, the path already exists. Integrated Services uses the Resource Reservation Protocol (RSVP) to create these paths. RSVP guarantees a quality rate of service, since this “priority path” is created in advance. Read the rest of this entry »

Defined in RFC 2281, HSRP is a Cisco-proprietary protocol in which routers are put into an HSRP router group. Along with dynamic routing protocols and STP, HSRP is considered a high-availability network service, since all three have an almost immediate cutover to a secondary path when the primary path is unavailable.

One of the routers will be selected as the primary (“Active”, in HSRP terminology), and that primary will handle the routing while the other routers are in standby, ready to handle the load if the primary router becomes unavailable. In this fashion, HSRP ensures a high network uptime, since it routes IP traffic without relying on a single router.

The hosts using HSRP as a gateway don’t know the actual IP or MAC addresses of the routers in the group. They’re communicating with a pseudorouter, a “virtual router” created by the HSRP configuration. This virtual router will have a virtual MAC and IP adddress as well.

The standby routers aren’t just going to be sitting there, though! By configuring multiple HSRP groups on a single interface, HSRP load balancing can be achieved.

Before we get to the more advanced HSRP configuration, we better get a basic one started! We’ll be using a two-router topology here, and keep in mind that one or both of these routers could be multilayer switches as well. For ease of reading, I’m going to refer to them only as routers.

R2 and R3 will both be configured to be in standby group 5. The virtual router will have an IP address of 172.12.23.10 /24. All hosts in VLAN 100 should use this address as their default gateway.

R2(config)#interface ethernet0

R2(config-if)#standby 5 ip 172.12.23.10

R3(config)#interface ethernet0

R3(config-if)#standby 5 ip 172.12.23.10

The show command for HSRP is show standby, and it’s the first command you should run while configuring and troubleshooting HSRP. Let’s run it on both routers and compare results.
Read the rest of this entry »

Whether you’re on the road to the CCNA, CCNP, MCSE, or you’re on any other computer certification track, the odds are that sooner or later, you’re going to fail an exam. It’s happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You’ve probably seen charts showing the growth of an industry or a business — you know, the ones that go from left to right, and look kind of jagged. The line goes up for a while, then down a bit, then up some more, then down a little.

The key? While every business has its setbacks, the net result is that the line goes up and progress is made. That’s how you want your certification pursuit and your career to go as well – upward!

I’m not asking you to be happy about failing an exam. You’re allowed to get mad for a few minutes, vow to never take another exam again, and be disappointed. What you’re not allowed to do is stay that way.
Read the rest of this entry »